Author / Post Admin Admin Group RCSB Owner/Founder Joined: July/22/2003 United States Posts: 5502 IP Logged Posted: April/02/2018 at 5:34pm  Quote   Join me in my shop as I talk about tools used by scale builders. This episode, I show how balsa strippers work for those that have never used one. You can find more information on these tools:  Master Airscrew Balsa Stripper https://amzn.to/3byoCOZ Xacto Balsa Stripper (Discontinued but you might find one on eBay or a local hobby shop) Click here to view the video. __________________ Mike Chilson, RCSB Owner/Founder -------------------- My R/C Scale Aircraft Over The Years   Back to Top  Printer Friendly Version  Profile  Search  Web    dirkske Lifetime Site Supporter Joined: March/22/2007 Belgium Posts: 198 IP Logged Posted: April/02/2018 at 11:57pm  Quote   For those with a 3d printer, put it to use and print a stripper for each relevant strip width. Search Thingiverse ex: https://www.thingiverse.com/thing:1892640   Back to Top  Printer Friendly Version  Profile  Search    lovetoflyguy Site Supporter Joined: July/03/2005 United States Posts: 50 IP Logged Posted: December/14/2018 at 8:03pm  Quote   I was so excited about this post.....differen't kind of stripper... __________________ Warbird Alley Big Sexy Aviation   Back to Top  Printer Friendly Version  Profile  Search    Bentwings Site Supporter Joined: January/21/2020 United States Posts: 344 IP Logged Posted: February/14/2021 at 6:23pm  Quote   I’m going to just add a tip I didn’t see spoken about. I’ve yet to see a perfectly straight balsa flat. The edge curvature is called camber. Be it wood metal or other supposedly straight material. So you go to the home store and ask for an aluminum straight edge about 3-4 feet long . Yes a yard stick is one name but in machine shop and other shop it’s called a scale or rule. Not ruler. It’s like motors and engines. Strictly shop talk. So get one of these straight edges preferably an anodized one, mainly because they have slightly rounded edges and are just a little harder.2” wide seemed best for me but I’ll go through the whole display looking for the one with the least camber. Dead straight is the “keeper one. Now to use this carefully bought piece. The project I’d to start lsying the planking or making parts with dead straight edges. Tak the chosen balso flat stock and lay it flat on the table. , wiggle the straight edge of the sluminum so it has about equal amounts to be trimmed off the sheet on each edge. You may want to clamp it down. Then take your exacto knif with a new #11 blade and slice the edge if the balsa sheet. This now gives you a working edge. Using you stripper again new #11 blade and cut strips what ever width you like. I use about 3/8” wide for fuselage and nacelle covering. Usually you can cut a number of strips before retriming . I’ve tried angle cuttin to make tighter seams but I just never seem to get good results. I use yellow glue as it sands easy when hard. I don’t use CA excep to stick them to bulkheads as it is very hard to sand.a little water and ammonia works wonders for shaping too. I don’t do sheets when planking as it’s too hard to hold alignment. I think this is old school but it sure works for me. I’ve seen dollhouse builders do this with ship lap sides that were so perfect it was scary. Byron Th __________________ Lifetime builder   Back to Top  Printer Friendly Version  Profile  Search    Russell Willis Basic Member Joined: February/12/2023 Australia Posts: 1 IP Logged Posted: March/09/2023 at 3:29am  Quote   Good advice all.   Back to Top  Printer Friendly Version  Profile  Search    Arngeir Blakseth Lifetime Site Supporter Joined: October/02/2009 Norway Posts: 644 IP Logged Posted: March/09/2023 at 3:59am  Quote   Best balsa stripper I have tried is one I bought from SLEC in the UK  few years back. It includes a 1m long aluminium U-channel that you attach to your bench or even better a piece of melamin faced chipboard. Your balsa sheet is held in position along this and that makes it easy to strip balsa and maintain a straight edge. It also is useful for checking how straight your balsa sheet is before you start stripping, many sheets do have a less than perfectly straight edge to them. https://www.slecuk.com/building-aids/balsa-stripper   Back to Top  Printer Friendly Version  Profile  Search

If you wish to post a reply to this topic you must first login
If you are not already registered you must first register

Similar topics you might be interested in... McLeod Balsa Stripper Dan McLeod Balsa Stripper?? Ep. 5 - BVM Clevis Pliers Ep. 9 - Plan Storage You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum

Copyright © 2003-2024, RCSCALEBUILDER.COM, All Rights Reserved